Magnetoresistive Sensor ICs

With a built-in magnetoresistive bridge integrated on silicon and encapsulated in a plastic package, magnetoresistive sensor ICs feature an integrated circuit that responds to low fields at large distances. Potential applications include laptops, material handling equipment, and pneumatic cylinders.

Design Criteria for HMC Components Application
Application

Size
(small/ smaller/smallest)

Price
(low/ lower/ lowest)
Performance
(good/ better/ best)
General CompassingHMC1022 / 1052LHMC1022 / 1052LHMC1052L / 1022, 1002
Compassing- AutomotiveHMC1022 / 1052LHMC1022 / 1052LHMC1052L / 1022
Compassing- Hand Held, GPSHMC1022 / 1052LHMC1022 / 1052LHMC1052L / 1022
Attitude ReferenceHMC1002 / 1022, 1052LHMC1002 / 1022, 1052LHMC1052L / 1022 / 1002
Metal DetectorsHMC1021S / 1041Z / 1052LHMC1021S / 1041Z / 1052LHMC1021S / 1041Z / 1052L
Vehicle/Traffic DetectionHMC1021S / 1041Z / 1052LHMC1041Z / 1021S /1052LHMC1052L / 1041Z, 1021S / 1001
Current SensingHMC1021S / 1052L / 1052LHMC1041Z / 1021S /1052LHMC1052L / 1041Z, 1021S / 1001
Vertical (Z- axis) SensingHMC1001, 1021Z, 1051Z /
1051ZL / 1041Z
HMC1001 / 1051ZL, 1051Z /
1021Z, 1041Z
HMC1051Z, 1051ZL / 1021Z,
1041Z / 1001
Position SensingHMC1501, 1512HMC1512 / 1501HMC1501, 1512

 

ss41 hall effect digital sensorvf401aps00b
Series2SS52M/SS552MTVF401APS00B
Descriptionomnipolar magnetoresistive
digital sensor IC
2-wire MR fine pitch ring magnet sensor IChigh resolution magnetic
displacement sensor IC
Magnetic
actuation type
omnipolardifferential bridgeanalog, saturated mode
Package
material and
style
2SS52M: plastic radial leads
SS552MT: plastic surface mount
(SOT-89)
plastic flat, TO-92-styleplastic surface mount (SO-8)
Supply voltage
range
3.8 Vdc to 30 Vdc4.5 Vdc to 16 Vdc1 Vdc to 12 Vdc
Supply current11 mA max.Icc operate: 16.8 mA max.
Icc release: 8.4 mA max.
7 mA max.
Output typedigital sinkingdigital current sourcesin(2Q), cos(2Q)
Operating
temperature
range
-40 °C to 150 °C
[-40 °F to 302 °F]
-40 °C to 150 °C
[-40 °F to 302 °F]
-40 °C to 150 °C
[-40 °F to 302 °F]
Measurements
(H x W)
2SS52M: 4,5 mm x 4,5 mm
[0.18 in x 0.18 in]
SS522MT: 4,2 mm x 4,5 mm
[0.16 in x 0.18 in]
2,8 mm x 2,9 mm
[0.11 in x 0.11 in]
4,9 mm x 6,0 mm
[0.19 in x 0.24 in]
Featuresomnipolar magnetics; sinking
output, low gauss operation (25
G max.); operating speed of 0 kHz to over 100 kHz; tape and reel available
wide speed capability; output pattern independent of gap between target and sensor; improved insensitivity to run-out, tilt, and twist; reverse polarity protectiondual analog voltages responding to changes in magnetic field angle; sine and cosine output;
accurate to 0,102 mm [0.004 in]; tape and reel available

 

Linear Sensor (Einzelne Magnetic Sensoren)
High SensitivityWilde Linear Range (+-6 gauss)
Series
Linear Sensor
HMC1001HMC1002HMC1021HMC1021ZHMC1021DHMC1022
Number Axis121112
Bridge Ohms8508501100110011001100
Number Pins82088816
Package TypeSIPSOICSOICSIPDIPSOIC
Sensitivity3.2 mV/V/OE3.2 mV/V/OE1.0 mV/V/OE1.0 mV/V/OE1.0 mV/V/OE1.0 mV/V/OE
Range+/- 2 OE+/- 2 OE+/- 6 OE+/- 6 OE+/- 6 OE+/- 6 OE
  same as HMC1001 but with 2 axes in 20 pin SOIC casesmaller size combined with linear voltage output signal, high sensitivemagnetic fields smaller than 85µ Gauss, very cost-efficient, especially for high quantities (OEM sector)

 

Magnetic SensorLinear Sensor Magnetic Sensor
wilde Linear Range, smallest Size

Series

MC1041Z Z-AxisHMC1051ZLHMC1052L 2-Axis
Number Axis112
Bridge Ohms110010001000
Number Pins8816
Package TypeLPCCIN-LineLCC16
Sensitivity1.0 mV1.0 mV/V/OE1.0 mV/V/OE
Range+/- 6 OE+/- 6 OE+/- 6 OE

 

Displacement Sensor
Saturated Mode Sensors

Series

HMC1501
Single Axis
HMC1512
Two-Axis
Number Axis120mV120mV
Bridge Ohms50002100
Number Pins88
Package TypeSOICSOIC
Sensitivity2.1 mV/Deg2.1 mV/Deg
Range+/- 45 Deg+/- 90 Deg

 

Linear Mode Integrated Sensors
HMC5883L Three-Axis
Compass IC
HMC6052 Integrated
Compass Sensor
HMC6343 Three-Axis
Compass with Algorithms
The HMC5883L is a magnetic sensor in a 3.0×3.0x0.9 mm surface-mount 16-pin leadless chip carrier (LCC) that includes Honeywell’s state-of-the-art, high-resolution magneto-resistive sensors with automatic degaussing (demagnetizing) strap drivers, offset cancellation and a 12-bit ADC for high resolution earth field sensing.The Honeywell HMC6052 is a 2-axis magnetoresistive sensor plus amplifiers and analog support features essential for compassing and low magnetic field sensing. The product is offered in a 14-pin surface mount 3.5mm by 3.5mm LCC package. Two channels of amplified sensor signals with a set switch function allow compass system designers to have a compact, easy to implement solution. Applications for the HMC6052 include electronic compassing and magnetometry.The HMC6343 digital compass circuit is three-axis magnetic and three-axis accelerometer compassing solution with tilt compensation. This 9.0mm by 9.0mm by 1.9mm multi-chip module with a UART interface plus command compatibility with the HMR3300/3400 compass solutions. The HMC6343 contains all sensors, microcontroller and analog support circuits plus all the firmware for heading computation and hard-iron calibration.

 

HMC 2003HMR2300HMR 2300R
Analog Magnetometer mit 3 AchsenKompaktes Digital MagnetometerDreiachsiges Strapdown Magnetometer

Compasses and Magnetometers – High Accuracy Magnetic Sensor & Compassing Solutions

Our extensive experience in fabricating magnetic sensors allows us to develop electronic compass modules that are suited for land, sea and airborne applications. Honeywell offers a complete line of HMR compass modules from the basic HMR3300 three-axis electronic compass to the HMR3600 with ± 80 degrees of tilt compensation. Our HMR compass modules offer high accuracy compassing solutions.

HMR3000 Digital
Compass Module
HMR3300 Digital Three-Axis
Compass
HMR3400 Digital Three-Axis Tilt Compensated CompassHMR3500 TruePointTM Compass ModuleHMR3600 µPOINT®
Compass Module
HMC6343 Three-Axis
Compass with Algorithms
HMC6352 Two-Axis
Compass with Algorithms
The HMR3000 is an electronic compass providing heading, pitch and roll information. Heading accuracy is 0.5 degree with 0.1 degree resolution. Tilt range is +/-40 degrees. Output update rate of 20Hz in RS232/485 NMEA format.The HMR3300 is a three-axis, tilt compensated compass that uses a two-axis accelerometer for enhanced performance up to a 60° tilt range. Heading accuracy is 1 degree with 0.1 degree resolution and 0.5 degree repeatability. Tilt range (Pitch and Roll) is ±60°. Compensation for hard iron distortions, ferrous objects and stray fields.The HMR3400 is a three-axis, tilt compensated electronic compass offering lower power consumption and increased miniaturization in a 0.6″ x 1.5″ PCB.The TruePointTM electronic compass is a 3 axis digital compass module that can be mounted and used in any orientation. Azimuth accuracy is 1 degree with 0.1 degree resolution and 0.5 degree repeatability.The µPOINT® (micropoint) digital magnetic compass is a new generation azimuth sensor that combines the latest in gyro technology with advanced digital magnetic compass hardware and software. Azimuth accuracy is 0.5 degree with 0.1 degree resolution. Inclination range is ± 80°. The gyro compensates for short term transient magnetic disturbances, keeping the heading output accurate, even in the presence of these unexpected magnetic fields.The HMC6343 digital compass circuit is three-axis magnetic and three-axis accelerometer compassing solution with tilt compensation. This 9.0mm by 9.0mm by 1.9mm multi-chip module with a UART interface plus command compatibility with the HMR3300/3400 compass solutions. The HMC6343 contains all sensors, microcontroller and analog support circuits; plus all the firmware for heading computation and hard iron calibration.The HMC6352 2-Axis Digital Integrated Compass On-A-Chip Solution combines a two-axis magnetoresistive magnetic field sensor from Honeywell, with the required analog and digital support circuits for heading computation. This product provides an electronic compass function using two-axis magnetic field sensing. Typical applications include; wireless phones with compassing, GPS/compass personal navigation, vehicle telematics and dish antenna positioning.

DRM™4000 – Dead Reckoning Module

Electronic dead reckoning is a proven methodology for providing supplemental position information in navigation systems.

DRM4000 Personnel Dead Reckoning Module
The DRM™ 4000 Dead Reckoning Module provides accurate position information for first responders and other people on foot in places that the global positioning system (GPS) is unable to reach. The small, easy-to-integrate unit contains ten sensors including three gyros, accelerometers and magnetometers as well a barometric altimeter to accurately deliver position location.

The DRM™4000 uses patented motion classification algorithms to analyze walking motion and compensate for unique user kinematics. The DRM™4000 contains an internal Kalman filter for integrating onboard sensors and external GPS data. It nominally provides position data that is accurate to within 2% of the actual distance traveled by a user in environments without GPS. The unit can be directly interfaced to many GPS receivers and man-pack computers and includes capabilities for accurate field calibration.

 

DRM4000 Personnel Dead Reckoning ModuleCondititionsMinTypicalMaxUnits
DimensionsPCB Assembly Only2.0 x 2.0
x 0.5
inches
Voltage RangeApplied to J1, Pins 1 and 42.83.35.2Volts DC
Current RangeBattery Voltage = 3.3 volts
No GPS Power Supplied
Battery Voltage = 3.3 volts
No GPS Power Supplied
mA
Serial DataRS-232C on J1 Pins 2 (RXD) and 3 (TXD)9600192038400Baud
Connector10-pin Samtech, SFSD
TemperatureOperating
Storage (OEM Only)
-40
-55
+85
+125
°C

We are looking forward to a good cooperation with you!


→ go back to product overview